Library
Classrooms
Curriculums
Articles
Pricing
Faculty
AudioPedia
Support
Login
Sign Up
Share
Go
or browse by category
Audio
Video
Graphics
Productivity
Web
Take a 13 question quiz to test and certify your knowledge of the tutorial-video course
Audio Mistakes 105 - 10 Common Panning Mistakes.
Get a mark of 80% or higher to pass this quiz!
1
What is hard panning?
It's when the Phase of the signal on the left is reversed relative to the signal on the right
It's when a signal is panned all the way to the left or right, in only one speaker
It's when the the Panning is automated, with a ping-pong effect between left & right
It's when the the Panning is automated, with an auto-pan effect
2
Pan Law can be set to...
guarantee that mono tracks will only be panned to hard left, center, and hard right
give you a guideline for panning mono and stereo tracks
automatically compensate for any level change between a signal panned center and panned to the side
automatically prevent a novice mixer from making poor Panning decisions
3
When setting Pan positions and maintaining a degree of symmetry for the mix...
mixers need to watch out for drum & bass tracks that run through the entire song
mixers need to watch out for solos performed by left-handed players
mixers need to watch out for changes in instrumentation from section to section
mixers should always pan guitars and keyboards hard left and right
4
When it coems to Panning, many modern mixes try to maintain...
some degree of symmetry in terms of instrument & vocal placement, between the L&R sides of the mix
a darker tonality in the center of the mix than on the sides
a wider dynamic range on the sides of the mix than in the center
a brighter tonality on the sides of the mix than in the center
5
A typical mixer's Pan Pot...
uses frequency differences between left & right for positioning
uses Phase differences between left & right for positioning
uses Harmonic differences between left & right for positioning
uses Amplitude differences between left & right for positioning
6
What is a popular technique for widening mono tracks?
Flipping the absolute polarity of the signal
Wide-panned micro-pitch-shifts and short delays
Running the track through an overdrive effect, which spreads out the added distortion harmonics
It is not possible to widen a mono track
7
Having tracks bunched up at the hard left, center, and hard right positions...
is the only correct way to pan when there are mono tracks in the mix
is a classic panning method from '60s stereo recordings, preferred by artists & producers
fails to take advantage of the potential increase in mix clarity & detail from more evenly spaced panning
is how audio engineers were able to turn old mono recordings into stereo
8
What happens if a pseudo-stereo image is created from a mono track by flipping the "Phase" of one side?
The track will play properly in stereo, even if collapsed to mono, under any conditions
The track will be heard in stereo even if the mix is collapsed to mono
The track will completely cancel if collapsed to mono before the audio hits the speakers
The track will be heard in mono if the mix is collapsed to mono
9
When positioned all the way to, say, the Left...
a True Stereo Panner will play both Left & Right in mono, while a Balance control will play only the Left
both a True Stereo Panner and a Balance control will play only the Left
a True Stereo Panner will play only the Right in mono, while a Balance control will play only the Left
both a True Stereo Panner and a Balance control will play both Left & Right in mono
10
When it comes to Panning conventions in modern mixing...
everything should be dead center
different approaches may be taken with different musical styles & genres
the same methods should be employed with all musical styles & genres
everything should simply be panned hard left, center, and hard right
11
M-S (Mid-Side) processing can usually widen the image of an alread) Stereo signal by...
raising the level of the Mid signal
raising the level of the Side signal
lowering the level of the Side signal
muting the Side signal
12
How can you get a True Stereo panner in Logic?
Make sure that the Channel Mode is set to Stereo
Use the Stereo Spread plugin
It is not possible to get a True Stereo panner in Logic
Use the Direction Mixer plugin
13
How can an Auto-Panner create Panning motion between left & right?
Via a pan knob
Via selective compression
Via an LFO
Via a LPF
Audio Mistakes 105
10 Common Panning Mistakes
You have answered
0
out of 13
questions.
You must
login
to take this quiz.
If you do not have an account, please
sign up
.
Get Your Grade
Cancel Quiz
Nice try! Unfortunately you didn't have enough correct answers to pass the quiz. No sweat! You can retake a quiz once per day.
-
-
You need 80% to pass this quiz
Retake Quiz
Back to the Course
View My Grades
Feedback
How are we doing?
We'd love your thoughts, feedback and questions regarding our new site. All feedback is appreciated!
We do not respond to this form! If you need support, please visit our
support page
.
Thank you for your input!
Your message has been successfully sent
Course Advisor
Don't Know Where To Start?
Ask A Course Advisor
Ask Us!
Copy the link below and paste it into an email, forum, or Facebook to share this with your friends.
copy
Make money when you share our links
Become an Ask.Video Affiliate!
The current affiliate rate is: 50%
Sign Up
Facebook
Twitter
Linkedin
Google+
Reddit
Pinterest
Classes Start Next Week!
Live 8-week Online Certification Classes for:
Logic Pro X
Learn More
Ableton Live
Learn More
Bitwig
Learn More
